Effect of boron oxide on the ionic conductivity of the Li1.2Al0.2Zr0.1Ti1.7 (PO4)3 ceramics with the NASICON structure

Capa

Citar

Texto integral

Acesso aberto Acesso aberto
Acesso é fechado Acesso está concedido
Acesso é fechado Somente assinantes

Resumo

Boron oxide is considered as a good dopant for improving the ionic conductivity of solid electrolytes. This effect is usually attributed to the optimization of grain boundary conductivity. In this work, the effect of addition of 1–4 wt. % boron oxide on the ionic conductivity of Li1.2Al0.2Zr0.1Ti1.7(PO4)3 with the NASICON structure was investigated. The obtained materials were characterized by XRD, SEM, Raman spectroscopy, IR spectroscopy, impedance spectroscopy and MAS 27Al, 7Li, 31P and 11B NMR. It was shown that the introduction of B2O3 at the stage of synthesis of Li1.2Al0.2Zr0.1Ti1.7(PO4)3 leads to the production of materials doped with boron ions. The highest conductivity (2.9 × 10–4 S/cm) at 25°C is characteristic of the sample with 2 wt. % boron oxide. At the same time, when B2O3 is added to the already prepared phosphate, it is predominantly localized at the interfaces, leads to the release of LiTiPO5 impurity and does not have a significant effect on the conductivity of the prepared samples.

Texto integral

Acesso é fechado

Sobre autores

A. Pyrkova

Kurnakov Institute of General and Inorganic Chemistry of Russian Academy of Sciences

Email: stenina@igic.ras.ru
Rússia, Moscow, 119991

I. Stenina

Kurnakov Institute of General and Inorganic Chemistry of Russian Academy of Sciences

Autor responsável pela correspondência
Email: stenina@igic.ras.ru
Rússia, Moscow, 119991

А. Yaroslavtsev

Kurnakov Institute of General and Inorganic Chemistry of Russian Academy of Sciences

Email: stenina@igic.ras.ru
Rússia, Moscow, 119991

Bibliografia

  1. Grey C.P., Hall D.S. // Nat. Commun. 2020. V. 11. P. 6279. https://doi.org/10.1038/s41467-020-19991-4
  2. Sang J., Tang B., Pan K. et al. // Acc. Mater. Res. 2023. V. 4. P. 472. https://doi.org/10.1021/accountsmr.2c00229
  3. Janek J., Zeier W.G. // Nat. Energy. 2023. V. 8. P. 230. https://doi.org/10.1038/s41560-023-01208-9
  4. Zheng F., Kotobuki M., Song S. et al. // J. Power Sources. 2018. V. 389. P. 198. https://doi.org/10.1016/j.jpowsour.2018.04.022
  5. Воропаева Д.Ю., Стенина И.А., Ярославцев А.Б. // Успехи химии. 2024. Т. 93. C. RCR5126. https://doi.org/10.59761/RCR5126
  6. Yu T., Yang X., Yang R. et al. // J. Alloys Compd. 2021. V. 885. P. 161013. https://doi.org/10.1016/j.jallcom.2021.161013
  7. Méry A., Rousselot S., Lepage D. et al. // Batteries. 2023. V. 9. P. 87. https://doi.org/10.3390/batteries9020087
  8. Stenina I., Novikova S., Voropaeva D., Yaroslavtsev A. // Batteries. 2023. V. 9. P. 407. https://doi.org/10.3390/batteries9080407
  9. Zhang Y., Zhan T., Sun Y. et al. // Chem. Sus. Chem. 2024. V. 17. P. e202301284. https://doi.org/10.1002/cssc.202301284
  10. Новикова С.А., Ярославцев А.Б. // Мембр. Технол. 2024. Т. 14. С. 288. https://doi.org/10.31857/S2218117224040047
  11. Arinicheva Y., Wolff M., Lobe S. et al. // Advanced Ceramics for Energy Conversion and Storage / Ed. Guillon O. Elsevier: Amsterdam, 2020. P. 549. http://dx.doi.org/10.1016/B978-0-08-102726-4.00010-7
  12. Stenina I.A., Yaroslavtsev A.B. // Pure Appl. Chem. 2017. V. 89. P. 1185. https://doi.org/10.1515/pac-2016-1204
  13. Kyono N., Bai F., Nemori H. et al. // Solid State Ionics. 2018. V. 324. P. 114. https://doi.org/10.1016/j.ssi.2018.06.016
  14. Rai K., Kundu S. // Ceram. Int. 2020. V. 46. P. 23695. https://doi.org/10.1016/j.ceramint.2020.06.143
  15. Saffirio S., Falco M., Appetecchi G.B. et al. // J. Eur. Ceram. Soc. 2022. V. 42. P. 1023. https://doi.org/10.1016/j.jeurceramsoc.2021.11.014
  16. Nuernberg R.B., Basbus J.F., Lux K.C. et al. // J. Phys. Chem. C. 2022. V. 126. P. 4584. https://doi.org/10.1021/acs.jpcc.1c09456
  17. Xu A., Wang R., Yao M. et al. // Nanomaterials. 2022. V. 12. P. 2082. https://doi.org/10.3390/nano12122082
  18. Cвитанько А.И., Новикова С.А., Стенина И.А. и др. // Неорган. материалы. 2014. Т. 50. С. 295. https://doi.org/10.7868/S0002337X14030142
  19. Zhang P., Matsui M., Takeda Y. et al. // Solid State Ionics. 2014. V. 263. P. 27. https://doi.org/10.1016/j.ssi.2015.01.004
  20. Kothari D.H., Kanchan D.K. // Ionics. 2015. V. 21. P. 1253. https://doi.org/10.1007/s11581-014-1287-9
  21. Kahlaoui R., Arbi K., Sobrados I. et al. // Inorg. Chem. 2017. V. 56. P. 1216. https://doi.org/10.1021/acs.inorgchem.6b02274
  22. Stenina I., Pyrkova A., Yaroslavtsev A. // Batteries. 2023. V. 9. P. 59. https://doi.org/10.3390/batteries9010059
  23. Грищенко Д.Н., Подгорбунский А.Б., Медков М.А. // Журн. неорган. химии. 2024. Т. 69. C. 155. https://doi.org/10.31857/S0044457X24020025
  24. Стенина И.А., Таранченко Е.О., Ильин А.Б. и др. // Журн. неорган. химии. 2023. Т. 69. C. 1683. https://doi.org/10.31857/S0044457X23601360
  25. Pershina S.V., Vovkotrub E.G., Antonov B.D. // Solid State Ionics. 2022. V. 383. P. 115990. https://doi.org/10.1016/j.ssi.2022.115990
  26. Kim Y.-C., Jung K.-N., Lee J.-W., Park M.-S. // Ceram. Int. 2020. V. 46. P. 23200. https://doi.org/10.1016/j.ceramint.2020.06.101
  27. Kang J., Guo X., Gu R. et al. // J. Alloys Compd. 2023. V. 941. P. 168857. https://doi.org/10.1016/j.jallcom.2023.168857
  28. Bai H., Hu J., Li X. et al. // Ceram. Int. 2018. V. 44. P. 6558. https://doi.org/10.1016/j.ceramint.2018.01.058
  29. Rumpel M., Appold L., Baber J. et al. // Mater. Adv. 2022. V. 3. P. 8157. https://doi.org/10.1039/D2MA00655C
  30. Zhu Y., Zhang Y., Lu L. // J. Power Sources. 2015. V. 290. P. 123. https://doi.org/10.1016/j.jpowsour.2015.04.170
  31. Das A., Sahu S., Mohapatra M. et al. // Mater. Today Energy. 2022. V. 29. P. 101118. https://doi.org/10.1016/j.mtener.2022.101118
  32. Jadhav H.S., Kalubarme R.S., Jang S.-Y. et al. // Dalton Trans. 2014. V. 43. P. 11723. https://doi.org/10.1039/C4DT01144A
  33. Peng H., Xie H., Goodenough J.B. // J. Power Sources. 2012. V. 197. P. 310. https://doi.org/10.1016/j.jpowsour.2011.09.046
  34. Ślubowska W., Kwatek K., Jastrzębski C. et al. // Solid State Ionics. 2019. V. 335. P. 129. https://doi.org/10.1016/j.ssi.2019.02.022
  35. Yan B., Kang L., Kotobuki M. et al. // J. Solid State Electrochem. 2021. V. 25. P. 527. https://doi.org/10.1007/s10008-020-04829-2
  36. Clemenceau T., Raj R. // MRS Commun. 2022. V. 12. P. 201. https://doi.org/10.1557/s43579-022-00162-z
  37. Minkiewicz J., Jones G.M., Ghanizadeh S. et al. // Open Ceram. 2023. V. 16. P. 100497. https://doi.org/10.1016/j.oceram.2023.100497
  38. Mariappan C.R., Gellert M., Yada C. et al. // Electrochem. Commun. 2012. V. 14. P. 25. https://doi.org/10.1016/j.elecom.2011.10.022
  39. Jonderian A., McCalla E. // Mater. Adv. 2021. V. 2. P. 2846. https://doi.org/10.1039/D1MA00082A
  40. Kobayashi R., Nakano K., Nakayama M. // Acta Mater. 2022. V. 226. P. 117596. https://doi.org/10.1016/j.actamat.2021.117596
  41. Stenina I.A., Velikodnyi Y.A., Ketsko V.A. et al. // Inorg. Mater. 2004. V. 40. P. 967. https://doi.org/10.1023/B:INMA.0000041330.84296.2e
  42. Francisco B.E., Stoldt C.R., M’Peko J.-C. // Chem. Mater. 2014. V. 26. P. 4741. https://doi.org/10.1021/cm5013872
  43. Barj M., Lucazeau G., Delmas C. // J. Solid State Chem. 1992. V. 100. P. 141. https://doi.org/10.1016/0022-4596(92)90164-q
  44. Arbi K., Bucheli W., Jiménez R., Sanz J. // J. Eur. Ceram. Soc. 2015. V. 35. P. 1477. https://doi.org/10.1016/j.jeurceramsoc.2014.11.023
  45. Kahlaoui R., Arbi K., Sobrados I. et al. // Inorg. Chem. 2024. V. 63. P. 7806. https://doi.org/10.1021/acs.inorgchem.4c00289
  46. Qiu D., Guerry P., Ahmed I. et al. // Mater. Chem. Phys. 2008. V. 111. P. 455. https://doi.org/10.1016/j.matchemphys.2008.04.045
  47. Duan J., Yu Y., Sun A. et al. // J. Power Sources. 2020. V. 449. P. 227574. https://doi.org/10.1016/j.jpowsour.2019.227574
  48. Yaroslavtsev A.B. // Russ. J. Inorg. Chem. 2000. V. 45. Suppl. 3. P. S249.

Arquivos suplementares

Arquivos suplementares
Ação
1. JATS XML
Baixar
2. Fig. 1. X-ray diffraction patterns of materials LAZTP-xB-syn (a) and LAZTP-xB-bm (b). Boron content (wt. %): x = 0 (1), 1 (2), 2 (3), 4 (4). The asterisk indicates LiTiPO5 reflections.

Baixar (60KB)
Metadados
3. Fig. 2. CR spectra of materials based on Li1.2Al0.2Zr0.1Ti1.7(PO4)3: 1 - LAZTP-0B-syn, 2 - LAZTP-2B-syn, 3 - LAZTP-2B-bm.

Baixar (41KB)
Metadados
4. Fig. 3. Fragments of IR spectra of LAZTP-xB-syn (a) and LAZTP-xB-bm (b). Boron content (wt. %): x = 0 (1), 1 (2), 2 (3), 4 (4).

Baixar (83KB)
Metadados
5. Fig. 4. MAS NMR spectra at 27Al (a), 7Li (b), 31P (c) and 11B (d) nuclei of LAZTP-4B-syn (1) and LAZTP-4B-bm (2).

Baixar (93KB)
Metadados
6. Fig. 5. Surface micrographs of LAZTP-0B-syn (a), LAZTP-1B-syn (b), LAZTP-2B-syn (c), LAZTP-4B-syn (d), LAZTP-0B-bm (e) and LAZTP-4B-bm (f) tablets.

Baixar (1015KB)
Metadados
7. Fig. 6. Temperature dependences of the total conductivity for the materials LAZTP-xB-syn (a) and LAZTP-xB-bm (b).

Baixar (84KB)
Metadados

Declaração de direitos autorais © Russian Academy of Sciences, 2025